| HS Code | 986811 |
| Chemical Name | Ethoxylated Trimethylolpropane Triacrylate |
| Abbreviation | TMPEOTA |
| Cas Number | 28961-43-5 |
| Appearance | Clear or pale yellow liquid |
| Molecular Weight | Average ~428 g/mol (varies by degree of ethoxylation) |
| Density | 1.08 - 1.13 g/cm³ at 25°C |
| Viscosity | 150-250 mPa·s at 25°C |
| Functionality | Triacrylate |
| Boiling Point | Decomposes before boiling |
| Flash Point | >100°C (closed cup) |
| Acrylate Equivalent Weight | Approximately 142-145 g/mol |
| Solubility | Miscible with most organic solvents |
| Refractive Index | 1.45 - 1.47 at 25°C |
| Polymerization Type | UV or free-radical initiated polymerization |
| Stability | Sensitive to light and heat |
As an accredited TMPEOTA (Ethoxylated Trimethylolpropane Triacrylate) factory, we enforce strict quality protocols—every batch undergoes rigorous testing to ensure consistent efficacy and safety standards.
| Packing | TMPEOTA is packaged in a sturdy 25 kg blue HDPE plastic drum with secure screw cap and clear labeling for safety. |
| Container Loading (20′ FCL) | 20′ FCL can load about 15-17 tons of TMPEOTA, packed in 200 kg drums or 1,000 kg IBC tanks, palletized. |
| Shipping | TMPEOTA (Ethoxylated Trimethylolpropane Triacrylate) is shipped in tightly sealed, chemical-resistant containers such as drums or IBC totes. It should be transported via ground or sea freight under cool, dry conditions, away from direct sunlight and incompatible substances. Shipping must comply with relevant hazardous material regulations, as it may be classified as a sensitizer. |
| Storage | TMPEOTA (Ethoxylated Trimethylolpropane Triacrylate) should be stored in a cool, dry, and well-ventilated area, away from direct sunlight and sources of heat or ignition. Containers must be tightly sealed to prevent moisture and contamination. Store away from strong oxidizers, acids, and bases. Use only approved, labeled containers, and ensure proper grounding and bonding to prevent static discharge. |
| Shelf Life | TMPEOTA typically has a shelf life of 12 months when stored in a cool, dry place, away from light and moisture. |
As a manufacturer specializing in TMPEOTA, we focus on supplying consistent material quality and formulation expertise to downstream industries that rely on this specialty acrylate monomer for advanced polymerization. Our experience covers several strategic application tracks, each with rigorous compliance demands, precise dosing protocols, and integration into specific production workflows yielding differentiated end products.
In the development of high-adhesion, fast-curing UV inks for paperboard, flexible films, and rigid plastics, TMPEOTA acts as a reactive diluent, delivering high crosslinking density and low migration attributes suited to food and pharma packaging. Ink formulators depend on its quick response in curing reactors to achieve press-ready sheets with minimized volatile content, while maintaining precise color depths and smudge resistance on high-speed lines. Our technical team consults on formulation ratios and process timing based on press trials and QC feedback, ensuring reproducible results under industry print standards.
Industry compliance standards
Typical usage ratio
Downstream process integration
Final product types
TMPEOTA is a key functional monomer in the preparation of UV-curable adhesive systems used in high-precision electronics manufacturing, including camera modules, touch panels, and micro-speaker assemblies. Its tri-functionality allows for tailored mechanical strength and dimensional stability post-cure, with low water absorption critical for electrical reliability during product lifetime. We support OEMs and contract assemblers in fine-tuning adhesives to process specifications, including automated dispenser viscosity windows and post-cure adhesion criteria.
Industry compliance standards
Typical usage ratio
Downstream process integration
Final product types
Wood flooring, kitchen cabinetry, and plastic trim part manufacturers use TMPEOTA to formulate high solids, rapid-cure clear and pigmented coatings that resist abrasion and household chemicals. The material’s role in the polyacrylate network brings a balance of hardness and flexibility, which is essential for floor coatings experiencing high foot traffic as well as molded plastic covers requiring scratch resistance during service. Our experts routinely assist with pilot-scale adjustments, considering line-cure speeds, lamp settings, and substrate pre-treatment compatibility.
Industry compliance standards
Typical usage ratio
Downstream process integration
Final product types
In the field of 3D printing for rapid prototyping and short-batch functional parts, TMPEOTA serves as a crosslinker in photopolymer resins for digital light processing (DLP), stereolithography (SLA), and LCD platforms. It is valued for imparting low shrinkage and strong cured detail definition, permitting designers and operators to produce intricate models and custom jigs directly from digital files. Resin manufacturers optimize usage according to the end-use mechanical requirements and resolution expectations dictated by their customer specifications.
Industry compliance standards
Typical usage ratio
Downstream process integration
Final product types
Leading manufacturers of optical fibers integrate TMPEOTA into secondary and matrix coatings to control modulus and ensure long-term fiber durability, as well as maintain process throughput on high-speed drawing towers. The chemical structure achieves fast surface cure under UV lamps, improving microbend resistance and environmental shielding needed in modern telecommunication networks. We have participated in multiple technical transfer trials at cable OEMs to optimize line speeds and cure depth, always referencing telecom industry reliability requirements.
Industry compliance standards
Typical usage ratio
Downstream process integration
Final product types
Dentistry and medical device ODMs use TMPEOTA as part of acrylate-based light-curable resin formulations to manufacture temporary crowns, dental trays, and custom orthopedic splints. Its multifunctional framework ensures instant set under visible light sources and delivers the required wear characteristics and color stability in intraoral environments. Formulation, process validation, and biocompatibility remain critical at every stage, and our technical specialists provide support for batch traceability and shelf-life extensions tailored to clinical supply requirements.
Industry compliance standards
Typical usage ratio
Downstream process integration
Final product types
Competitive TMPEOTA (Ethoxylated Trimethylolpropane Triacrylate) prices that fit your budget—flexible terms and customized quotes for every order.
For samples, pricing, or more information, please contact us at +8618105193818 or mail to sales11@bouling-chem.com.
We will respond to you as soon as possible.
Tel: +8618105193818
Email: sales11@bouling-chem.com
Flexible payment, competitive price, premium service - Inquire now!
On our production floor, TMPEOTA isn’t just another entry in a catalog—it’s the product of decades of testing, raw material vetting, and an eye for what consistently produces the cleanest, most reliable oligomer for radical-cure applications. Every shift I’ve worked, I’ve seen its value both in how it runs through our systems and in how our partners put it to work in theirs.
TMPEOTA, or Ethoxylated Trimethylolpropane Triacrylate, combines a backbone of three acrylate groups with a tailored ethoxylation chain. Our most requested model achieves an average ethoxylate content that balances viscosity and flexibility, but over years, we’ve expanded runs to different degrees of ethoxylation. Through careful control at the reactor, we've learned to achieve the right mix for customers needing different reactivity or lower shrinkage. The real advantage comes out in the way it builds crosslinks. TMPEOTA’s tri-functionality puts it in a sweet spot—it’s more reactive and forms higher-density networks than difunctionals, but stays more usable than tetra-acrylates, which can easily tip into brittleness and high shrink.
Acrylic photopolymer chemistries have evolved dramatically, but since we started scaling up for UV-curable systems in the late ’90s, TMPEOTA has proven one of the most resilient pillars. From the view in the kettle, it looks like a nearly water-white viscous fluid, but every operator knows to keep an eye on color and stability—especially at the purification step. Since customers count on minimal yellowing in clear coats and on controlled viscosity for application, we pay extra attention to inhibitor load and moisture control. Experience has taught us that even small changes in batch water content can steer reactivity and shelf life.
On paper, TMPEOTA’s properties—viscosity, acid value, color, reactivity—usually read as a shortlist, but the difference we see from batch to batch tells the real story. The typical viscosity lands in the range of 150-300 mPa·s at 25°C, balancing flow for easy mixing and enough body for steady application, depending on the ethoxylation. Acid value, which always takes a beating if you rush the washout or skip on resin stabilization, often sits below 0.5 mg KOH/g in our best batches. That low acid translates directly to resin stability—the color stays lighter longer; the polymer doesn’t go tacky on the shelf. In acrylates, color stability is the whole game for applications like clear overprints and high-end coatings.
Sometimes, customers ask about functionals—how many acrylate groups attach to the backbone. There’s a reason the triacrylate version remains favored. TMPEOTA brings three acrylate groups to each molecule, giving stronger cure and network density. Compared to diacrylates, which produce softer, more flexible films, TMPEOTA’s cured films offer greater chemical resistance and hardness. Compared to tetra-acrylates, TMPEOTA is easier to control; tetra-acrylates almost always run into issues with shrinkage and brittle failures. Working directly with TMPEOTA, you get toughness and resilience without the side effects that can ruin a high-value print run or an industrial finish.
In every corner of the UV-cure market, TMPEOTA is a common ingredient. On press floors, it’s found mixed into pigmented or clear inks, letting lines run faster because it cures instantly under UV LEDs. Our operators hear from ink formulators every year—they want predictable curing behavior, no surprise yellowing, and a product that resists sweating or phase separation over time. The high reactivity of TMPEOTA deals with shadow curing and surface tack. In high-solid formulations, its structure cuts down on residual shrinkage, which keeps labels flat and print jobs looking sharp.
For industrial wood coatings, TMPEOTA is almost always present in the hard top layers. Cabinet and flooring manufacturers want finishes that resist spills, abrasion, and chemical attack from cleaning products. Our TMPEOTA batches are built for consistent cure; once the UV lamp flashes, the coating locks in and grabs tight to the substrate. The difference in scratch resistance and water soak comes directly from how tight TMPEOTA crosslinks on cure. The ethoxylate chain adds just enough flexibility that the finish doesn’t crack or haze as temperature swings. I’ve walked a few flooring manufacturers through our plant who care just as much about how the resin smells out of the drum as about how tough it sets—TMPEOTA always gets a nod for its stability and minimal odor once it’s cured.
On the electronic side, TMPEOTA goes into conformal coatings and potting compounds. Component makers need resins that cure without leaving ionic residues or VOCs, which lead to failures after soldering or in field use. We monitor ethylene oxide residuals and control inhibitor to keep potting resins clean and reliable. The network-forming quality of TMPEOTA provides electrical insulation and surfaces that stand up against humidity migration and breakdown. Every batch bound for electronics gets extra purity checks, because a minor slip on metal ion contamination shows up quickly in high-voltage breakdown later.
Not all acrylic oligomers behave the same way under the UV lamp or in two-part mixes. On the supplier end, we’ve tested runs of diacrylate and tetra-acrylate alternatives, both as blends and as pure resins. Diacrylates like Ebecryl 810 are used where soft, flexible materials are called for—think soft-touch finishes or labels that need bending. Yet, these struggle in applications needing high abrasion resistance or a truly tight crosslink network. Our TMPEOTA, in contrast, gives stiffer, harder films that take more wear.
The high-functionality acrylates, like pentaerythritol tetraacrylate, look tempting on paper for their reactivity. In practice, users report that cured coatings get too brittle and shrink enough to cause delamination, especially when higher lamp energy is used or thick coatings are called for. Over years of supporting both R&D and production users, it’s clear that TMPEOTA forms a Goldilocks zone—balancing speed, toughness, and flexibility. End users get reduced shrinkage, long-term clarity, and a spread-out cure window. For us as manufacturers, this means fewer complaints about batch-to-batch variation, easier stock management, and less troubleshooting on customer lines.
Sometimes users try to substitute other trifunctional acrylates, but the difference comes down to the ethoxylation. Too-low EO content produces a hard, brittle coating that can crack on flex. Too-high EO, meanwhile, turns the resin rubbery and brings down chemical resistance. We keep data on reactivity, film hardness, gloss, and weatherability from side-by-side lots; our most popular TMPEOTA balances molecular weight with chain flexibility so that it doesn't break or haze under stress. That experience comes from years of application testing and working with both adventurous startups and established brands.
Over the years, we’ve invested in both quality control and raw material procurement. High-purity EO and TMP feedstocks come only from qualified suppliers. From the day fresh drums roll into our plant, we test for trace acid, free monomer, and moisture. The reactor stage is where things can go sideways—over-ethoxylate and you lose reactivity, under-react and the viscosity jumps, which means slower mixing and incomplete cure later on. There’s no shortcut to getting it right; every batch ships with retention samples, and we keep those for trending, should any complaints trickle back. Most customers never even realize how much time goes into policing color and reactivity drift.
Packaging matters as much as process. TMPEOTA ships in industry-standard drums or intermediate containers, flushed and stabilized to keep inhibitors at workable levels. We monitor storage temperature closely—TMPEOTA likes to stay cool, and exposure to sunlight or excess heat can reduce shelf life. Over the years, we've seen seasonal differences in how quickly batches age, so temperature and stabilizer loads are adjusted accordingly. Most end users never see a problem, but we always keep watch, since a hot spot in a warehouse can start the clock ticking on gelling.
From the view at our loading dock, TMPEOTA leaves in containers bound for every part of the world—printing lines, wood finishing operations, electronics assembly plants. Every application leverages a different part of the product’s profile. In flexographic and offset printing, users appreciate the way TMPEOTA cranks up cure speed and depth. Shorter dwell times mean more output on modern presses, without waiting for lingering wet tack. The cured layer stands up to rub, oil, and water because of the dense crosslinking you get at the molecular level. Ink formulators have told us the consistency of gloss and clarity is why they stick with our material; unpredictable curing or surface scumming can cost a high-profile customer and weeks in troubleshooting.
For adhesives, TMPEOTA brings a unique blend of low viscosity and high reactivity that lets formulating chemists work with higher loadings of fillers or modifiers without sacrificing cure quality. Pressure-sensitive and assembly adhesives gain both tack and final strength, and our in-house testing always pushes formulations to peel, shear, and environmental exposure limits. Since adhesives often need to pass regulatory flame or toxicity testing in multiple countries, our control over impurities becomes not just a benefit, but a necessity.
Automotive coatings demand every quality—clarity, scratch resistance, UV stability, and chemical toughness. We tune ethoxylate content batch by batch based on what our auto customers request, since they know some models need a harder finish, others more flexibility for interior parts. Each year, we coordinate with their labs as specifications inch tighter, for instance on non-yellowing after QUV or acid resistance from bird droppings. The requests may shift, but TMPEOTA’s core structure continues to hold up in every decade of automotive formulation.
Manufacturing TMPEOTA isn’t without its headaches. Photoinitiator compatibility sometimes comes up: not all systems cure at the same rate. Over the years working with customers who run high-speed lines, we've documented which initiators pair best with different TMPEOTA grades. Our data shows that Type I initiators like benzoin ethers fit most flexo and screen inks, but for deeper section cures or thicker industrial coatings, users may need a blend involving Type II photoinitiators. We’ve trialed these combinations on our in-house UV lines so customers don’t waste days cycling through trial-and-error.
Odor and migration always spark debate, especially in packaging. Some markets, especially food contact or sensitive medical packaging, cannot tolerate leachables or strong odors. We've systematically tracked and reduced residual acrylate through adjusted purification, and every lot bound for packaging labs gets an extra odor check. Raw material purity, synthesis pathway, and careful vacuum stripping keep free monomer below targeted thresholds.
Risk of yellowing in outdoor or clear applications caused us to develop a tracing system for UV stabilizers and antioxidants that go into blends with TMPEOTA. Our partners in outdoor advertising, construction, and protective coatings need long-term clarity. After years watching field failures where a small change in stabilizer package tipped the performance curve downward, we built a tracking database so every pigment and additive inclusion ties back to a resin lot. That takes some extra paperwork, but it stops finger-pointing and lets us help troubleshoot if something goes wrong down the supply chain.
Supply chain interruptions have tested every chemical manufacturer in recent years. We learned to keep documented backup suppliers and test new drums as much for trace metal and color as for paperwork validity. We hold ongoing training for operators and QC on how to test for low-level impurities and screen for red flags in new shipments. Those steps pay off when a project deadline depends on a critical resin load, and we can both assure and prove our shipment matches last year’s results.
Every year brings new application demands—aerospace sealants, 3D print resins, LED-cure dental materials. We run pilot synthesis with these in mind, tuning the EO chain and reactivity based on where the final product goes to work. For 3D printing, TMPEOTA’s balance of viscosity and high cure speed lets formulators achieve uniform layers without sagging, but the shrinkage control remains crucial. Dental materials put every impurity under a microscope, so we commit to running lots destined for those users under extra-tight controls.
As sustainability pressures grow, many in the industry are experimenting with bio-based co-oligomers and process optimizations aimed at lowering carbon output. We’re pursuing greener EO sources and genetic TMP production, testing how these changes affect TMPEOTA's final behavior. Early results show some minor shifts in cure speed and film toughness, but our in-house team continues to collect long-term data before rolling out greener grades broadly. If there’s one thing we’ve learned, it’s that performance in the field can’t be compromised for a minor sustainability gain—demanding applications require every bit of the reliability we've built into every batch.
From the shop floor to the end-user’s application line, TMPEOTA continues to serve as a dependable workhorse, shaped by real-world feedback, iterative process improvements, and the kind of quietly obsessive QC that most only notice when something goes wrong. Our teams keep chasing smaller impurities, steadier color, and purer reactivity profiles. The measure for us isn’t just a spec sheet or test certificate—but the call from a formulator a year later saying the product just works, every time it pours from the drum. That’s what keeps TMPEOTA at the forefront of UV-cure technology and why we continue to invest in getting every batch right, down to the last drop.
Get in touch with our team to discuss your chemical product requirements, request samples, or explore how we can support your business with tailored solutions.